B12 2-Wire Modular Gas Detector

By: Analytical Technology  06-Dec-2011
Keywords: Gas Detection, Digital Display, Detection and Alarm

ATIs B12 2-Wire Modular Gas Detector is a flexible component system providing a variety of options to meet individual gas detection and alarm requirements.  Series B12 transmitters are loop-powered instruments that transmit a 4–20 mA signal linearly proportional to gas concentration. 

Transmitters are normally supplied with the sensor close coupled to the enclosure. However, for special applications, the unit can be supplied with separate sensors that can be located up to 25 feet from the transmitter. Sensor duct mounting adapters and sensor flowcells can also be provided for specific applications.

When remote display and alarm relay functions are required, the B12 Wet Gas Transmitters can be connected to ATI's B14 Alarm Receiver System. This system will provide direct digital display of gas concentration, plus 3 alarm setpoints, remote alarm reset input, and retransmitted 4-20 mA output. Or, the B12 transmitter may be used separately and tied directly to the users' DCS, PLC, or other equipment.

Universal power supply modules provide DC power to receivers. The power supply is housed in a compact module similar to the receiver, and will accept inputs from 85 to 265 volts, AC or DC, without adjustment. The power supply also provides a power failure relay and charging for an optional battery back-up unit.

Keywords: Battery Back-Up, Component System, Detection and Alarm, Digital Display, Gas Detection, Universal Power Supply,

Contact Analytical Technology

Email

Print this page

Other products and services from Analytical Technology

06-Dec-2011

A14/A11 Stationary Gas Monitor

Receivers may be located up to 1000 feet from sensor/transmitters for remote indication, or can provide local control functions such as valve shutoff while transmitting a 4-20 mA signal to remote displays or data loggers. From chemical and petrochemical plants to food processors, the GasSens system can be applied to the simplest or most complex gas detection application.


06-Dec-2011

F12 Toxic Gas Transmitter

The MODBUS™ protocol supports 9600 baud access to concentration and status information, and supports alarm setup and many other functions on either RS485 or RS232. The HART™ protocol supports the HART™ Universal and Common Practice Commands at 1200 baud using the Bell 202 FSK modem standard. ATIs F12 Gas Transmitter is designed to measure toxic gas in hazardous locations requiring an Intrinsically Safe device.


06-Dec-2011

D12 Toxic / Combustible Gas Detector

The MODBUS™ protocol supports 9600 baud access to concentration and status information, and supports alarm setup and many other functions on either RS485 or RS232. For many toxic and combustible gases, ATI offers a unique sensor response testing system unmatched by any competitive transmitter. ATIs D12 Toxic Gas Transmitter will accept up to 46 different sensors, greatly reducing the need for multiple transmitter models.


06-Dec-2011

B14 Gas Alarm Module

ATI’s Series B14 Gas Alarm Module Receivers are compact electronic modules that provide local alarm, display, and signal retransmission functions for gas detection systems. They’re ideally suited for use with ATI’s Series A12 or B12 two-wire toxic gas transmitters, or Model A12-17 or B12-17 three-wire combustible gas transmitter. Each relay can be assigned to any setpoint to allow multiple alarm functions at a single alarm point.


06-Dec-2011

D12IR Infrared Gas Transmitter

The D12-IR utilizes a compact IR sensor in a corrosion resistant housing with sintered flame arrestor to meet hazardous area classification requirements, and is suitable for most plant environments. While catalytic LEL sensors offer reliable service, the presence of silicon vapors, hydrogen sulfide, and halogenated hydrocarbons can quickly degrade sensor performance.


06-Dec-2011

C16 Portable Gas Detector

ATIs Series C16 PortaSens II Portable Gas Leak Detector is a versatile tool for performing regular leak checks in gas storage areas, around process equipment and piping, or in confined spaces prior to entry. A unique feature of the C16 detector is its ability to measure a variety of different gases by simply inserting the appropriate sensor for that gas.